On this page in the next paragraph you can get a good deal of worthwhile insight in regards to How to Install a Bathtub Yourself.
Mounting a bath tub isn't specifically rocket science, however it does need solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old bath tub with a new one is also a reasonably hard task. If the old bathtub is easily available, the project can move quickly; if you have to open a wall to remove the old tub and also place the brand-new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will require an assistant to leave the old bathtub and also embeded in the new one. Ensure you have qualified yourself for the task and also are comfortable attempting it. Instead of working with a contractor to take control of a halfway-completed task, it is better to think about using one before you begin. Chances are you might require a professional plumber to make tube connections.
This write-up will certainly assist you install a new bath tub in your restroom if you have actually currently purchased a brand-new tub as well as don't need to alter the plan of your previous water pipelines.
Your tools and also product list ought to consist of the following:
Getting ready for the Installment
First of all, the sustaining framework provided with the bath ought to be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its last setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of removing the existing faucets can be fairly troublesome due to the limited accessibility that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the bath tub in the required setting. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable tap port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Activate the water and check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise examine the overflow outlet and the normal outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will resolve it right into its final position.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washers are in location between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The former type should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, triggering the water to pass through the wall in between the bath and the tiling, causing problems with moisture and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and cartridges, and also are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Bear in mind to always load the tub with water before sealing, to permit the motion experienced when the tub is in usage. The sealant can crack rather early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about Installing A Bathtub. Thanks a ton for taking time to read our post. You should take a moment to promote this article if you enjoyed it. Many thanks for your time. Come back soon.
Get Quote Now